Tuesday, 12 May 2020

Rear End Finished

Been working hard during lock down and enforced holidays.

The beetle body work has 8 phases to completely repaint the whole car!

Phase 1 Rear wings Phase 2 Valance Phase 3 Deck lid have now been stripped, rust converter, filled, sanded, primed, sanded and painted with 2+2 Colour coats.





All primed with epoxy primer

Epoxy primer is really tough and sticks well. Just does not have a very good final finish. Left it to dry for 48 Hours to fully harden.

Then sanded it down with 320 grit. As it's so hard it very hard to sand down flat. Slight textured finish.  I was worried about sanding it down too much as I might cut through the primer and end up with the horrible reaction with the paint underneath.

Next time I might put a coat of the P88 High build primer over the epoxy to get an easy to sand flat finish before top colour coats.





Final 2+2 Top colour coats


So the paint went on well. First two coats mixed paint:thinner of 50:50 and the last 2 coats mixed to 40:60 to give a better flash coat with more solvent thinners.

Happy with the top colour coats shine BUT there is an underlying texture from the epoxy primer.

So moved on after a few days to dry and harden to get stared with the rebuild.















Final Build up completed. 

Once final build up was done only a few snags with grommets for lights and bumper mounting. Everything went together well.

Also pumped in 2.5 litres of gearbox oil as i had changed the swing axle gaiter boots while it was easy to access.

Put the wheels back on and drove up the road.



So finished the rear end! Pleased with the result!


Now to move onto the front end!..........


Bad Reaction!

Started to paint the Rear Valance and deck lid.

The paint system I "was" using was as follows:

UPOL Acid Etch #1 - Bare metal primer
UPOL P88 High Build primer - on filler or existing paint
Cellulose Cobalt Blue - Top colour coats

So for the wings I followed the following paint system:

Paint stripped to remove all layers
Chipped out any filler
Bare Metal.

Rust converter
Sand down
Acid Etch Primer 2 Coats
Sand down
Filler work
High build primer 2 coats
Sand down
Top Coats 2 + 2 

That worked well for the wings and wanted to use cellulose paint system as its the original paint system.

Then on the Deck lid and Valance. As this was already painted and flat my plan was to sort any localized issues and paint as above just without the Acid Etch as it eats away the thin edges of paint and filler.

So Sanded down. Treated any rust. Skim filler in low spots.



So all was ready to go.

Loaded up the spray gun with Upol P88 High build primer. Mixed it to a 70:30 thinners (unlike the datasheet which says 50%!)

Spray going really well. Then moved on and turned around to see this happen!





The paint was not even holding its own weight!

It was not happening on filler but only on the old painted areas!

So after a spell of depression and despair I sanded the whole lot off and did some research.

I suspected that the previous owners had used Acrylic Paint! It's an incompatibility issue with solvents on oil based acrylic.

So I did a few test spots to confirm with different ratios of Solvent.





Sure enough same reaction! It does hold when more paint less solvent is applied but still reacts around the edges!

So I need to rethink the plan. Could use a barcoat to act as a barrier but any pinholes will cause a reaction.

So decided to try some Epoxy Primer.




So I am going to to have to cover it all with epoxy primer!

Epoxy primer is much better for rust and durability BUT it's also twice as expensive and harder to sand down flat. But needs must!

More progress to come........

Tuesday, 5 May 2020

Rear Wings

Continuing to work on the Beetle during lock down.

Spent a while cutting back and filling on the etch primed wings. The left passenger wing had some battle scars.

During Guide coating:







One day was too windy to spray paint so spent some time painting the rear wheel arches.




Rust Converter




Epoxy Mastic


Put two additional coats of high build primer on the wings:



Outdoor body shop! With seating area!

Top Colour Coats applied:









Really like the finish. A little orange peel but should cut back nicely. Really liking the colour and depth.


New DubZen Post

 New Dubzen post: https://dubzen.blogspot.com/