I have managed to solve the issues Gus as been having with the lumpy idle & hesitation.
So after the last post I decide to investigate the ignition system as there was a small mis-fire sometime at idle.
So the plan was to swap out all ignition components one by one.
Finally all that was left was the coil..... So I did not have a spare one so I managed to find a Pertronix Flame thrower coil off e-bay - Returned one from JK and sold via status VW on e-bay.
So It was £30 and had slight damage on the top BUT a saving of at least £20 on new.
Arrived next day and fitted it on Thursday Night.....
WOW what a difference. The idle is smooth and it has also massively reduced the hesitation! GREAT
Best money I have spent and it goes perfectly well with the Pertronix Ignigtor electronics points.
So Gus is like new and goes SO MUCH BETTER!
No I can get the back end out in the Wet!
Monday, 23 October 2017
Monday, 16 October 2017
Lumpy Idle
After driving Gus everyday to and from work clocks up 32 Miles everyday.
No so bad but can take a toll on especially sitting in rush hour traffic.
BUT he does himself and me proud every day and still smiles per miles....
He has been causing a few worrying moments where he has a very lumpy idle. Very low RPM and also plenty of engine shake.
Initially I though an engine running on 3/4 cylinders but upon revving the engine it sorts itself out and he is still happy at 70mph with no loss of power.
So last weekend I did my typical see whats wrong.
1. Compression Test - Same a last time. Cylinder 2 lower at 105, rest OK at 120 but no worse.
2. Tappets reset - 2 slightly tight at 0.18 reset to 0.15
3. Plugs, HT leads, Rotor & Cap checks - All okay swapped each and no issues
Plug on No 2 was black around top insulator- Could have been loose and blowing but cleaned and reset and swapped to a different cylinder.
Most plugs look a little rich BUT tips look normal and not completely soot covered black.
Also better rich and cool than lean and burned!
So after all that it idles better and more stable BUT I still get a random misfire noise - Not exactly a misfire at idle just a pinging noise randomly a few time a minute.
Occaisionly I also get a lumpy idle as well.
I have checked and swapped everything in the ignition except the coil.
so it could be:
1. Random air leak - Air leaks are worse at idle but don't typically cause misfire
2. HT coil arcing - Could explain misfire
Will pick up a replacement coil and see and check with the WD40 spray test
Friday, 18 August 2017
Gus Improvements so far
So Gus has been with us for a few months......
So far I have completed the following work:
So far I have completed the following work:
- New Exhaust - Rear box was leaking
- Replaced Fuel All fuel line - Leaks and cracks along most rubber pipe - Worse one was under the tank.
- New Carb - Original Solex 34 Pict 3 was leaking from throttle shaft - Replaced with cheap "Empi" plan to get the original Solex re-built at some point
- New Distributor - Getting rid of the 009 - Went for new SVDA re-pro - Again I will find a second hand Bosch / VW when I find a good one.
- Replaced Spark plugs
- Replaced HT leads - Bosch Mexico one was broken out the box!
- New Distributor Cap, Points & rotor.
- Removed Tar Paper from Engine bay - Saggy as a wet flannel when hot
- Oil Changed
- Tappets done
- Timing & Carb Basic setup
- Fitted a "save my bug" oil temperature sensor
- New heater pipes from fan housing to heat exchangers
So after all this work my observations where:
- Great to drive when at low rpm there is hesitation and engine bogged down at low rpm. Picks up at higher rpm.
- Spluttering & Hesitation was only improved when timing was set to 10-12 degrees BTDC (Way too advanced) and around 40-45 at 3000rpm
- After a few drives the timing & points gap would need resetting. Idle rpm was low and stalling. Dwell angle was all over the place.
- Spluttering was much worse when cold
- Back fire when not accelerating (ie Idle rpm) but still moving - Engine breaking or downhills. Only little popping.
So after a few weeks use decided to upgrade alter a few things to get hesitation and spluttering.
- Checked compression - All about 105 psi but one at 90psi - Not as bad as I expected.
- Vacuum check - Again all withing the good range
- Points replaced with Petronics electronic points - This was simple, easy to fit and much improved.
- New Vacuum advance unit - My distributor was only 1 month old but the vacuum unit had failed
So after these mods the electronic points give much better idle, spark smooth rpm throughout the range. Idle is a little high around 800-900. Vacuum advance stops the little backfires as retards the timing when throttle closed.
Managed to get the timing at 7.5 BTDC and full advance around 35 TDC at 3000 rpm. So much happy cooler engine
Hesitation and splutter - still there when cold (after choke has gone off) but only for about 5-10 minutes its fine.
What I am thinking is that the lack of thermostat & pre-heat of air and pre-heat of TP manifold (Both exhaust pre-heater are blocked) its a small amount of carb icing and also the fuel accelerator pump fuel is not atomizing due to the cold air and cold manifold.
Plans for engine work is:
1. Thermostat - Got an original working one but flaps feel a little sticky so wait until I drop the engine
2. New manifold - Got an orginal TP mainfold - Need to unblock the pre-heat tubes and wait until engine is dropped.
3. Rebuilt Solex - Get my old carb rebuilt - Wait until I got the money!
4. Inlet Air Pre-heat - Got rear tin and stove pipe BUT my airfilter is 1966 version (Pipe on left) and need to find a good secondhand air filter with pipe on right.
5. Sort out end play - See if I can set end float with some shims. Drop engine.
6. Front Engine doghouse tin - Need to get some front tin to replace crappy chrome one (too many holes due to bending)
Anyway I have grown to love "Gus" he has become one of the family and looking forward everyday to drive him to work!
Here are a few pics of the engine.
Next Posts - History of Gus from Previous owner restoration & Plans for next work! - coming soon
Tuesday, 13 June 2017
Welcome Gus - 1968/69 VW Beetle
Welcome Gus the Cobalt Blue 1968/69 VW Beetle!
Purchased this beetle last week and wanted to create him a new Blog.
We now own two aircooled VWs
Betty (2004 VW Brazilian Type 2c Bus)
Gus (1968/69 VW Beetle Type 1 Bug)
Purchased this beetle last week and wanted to create him a new Blog.
We now own two aircooled VWs
Betty (2004 VW Brazilian Type 2c Bus)
Gus (1968/69 VW Beetle Type 1 Bug)
Subscribe to:
Posts (Atom)
-
So this weeks task was to try to get better bonnet alignment. So I had been bugging me that the drivers side bonnet alignment was about 2c...
-
Next on the list now that both sides are done was the worst job. The roof needs painting and around the windscreen and in front of it. So t...









